GPS Splitter

GPS Splitter

GPS Splitter

When you need the GNSS signal routed to multiple destinations GPS Source, available from APC Time, has the most extensive line of GPS splitters in a wide array of output and housing form factors. We provide everything from passive splitters to units that can have custom gain on each output.

For expert technical and product advice, contact our team today on 01522 596 570 or email time@apcplc.com

APC Technology Group plc

GPS 1×4 Timing Splitter – S14GT

Designed for the L band frequency, the S14GT makes it possible to use a single GPS referencing antenna and cable arrangement for multiple synchronisation systems.

The S14GT features an antenna DC bias select circuit. This allows for the active antenna DC input to be applied to any or all RF outputs. With this feature, one DC voltage will be chosen to power the antenna while other inputs will be switched to DC loads. Designed for redundancy, if the selected DC bias input should fail, the DC bias will automatically switch to another DC input to ensure an uninterrupted supply to the active antenna.

  • Delivers L band frequency signals to multiple GPS synchronisation modules and receivers
  • Amplified to offset splitter losses
  • High isolation
  • Also available with 0dB gain
APC Technology Group plc

GPS 1×8 Timing Splitter – S18GT

The S18GT will support long-lasting, trouble free deployment in a small cell wireless and/or DAS environment. The device makes it possible to use a single GPS referencing antenna for synchronisation systems, increasing capacity without increasing GPS antennas or cabling requirements.

Power is obtained from the GPS receiver(s) connected to the amplifier.  There is no need for a separate DC power supply or wiring. DC power applied to the splitter is also passed on and utilized by an active antenna. It can obtain power on any of the four outputs from a GPS receiver connected to any port.

  • Delivers L band frequency signals to multiple GPS synchronisation modules and receivers
  • Conveniently powered from a GPS receiver on any output port
  • Amplified to offset splitter losses
  • Optimum signal quality with low noise and high gain
  • High isolation will eliminate receiver interaction
APC Technology Group plc

GPS 1×2 Tiny Splitter – S12T

A tiny splitter that still delivers full-size performance, the S12T is perfect for unmanned aerial vehicles (UAVs). With a rugged metal enclosure, it has been designed for long-term durability. The S12T will allow the power from one GPS antenna to be split between two GPS/GNSS devices. It can be used with any existing antenna and cable such as GPS Source’s RG316, a common aircraft rated cable good for short distances.

  • 1.875 ” 1.75″ X .475″
  • 30 grams
  • SMA(f) connectors
  • Lightweight, low profile design, waterproof option
  • Low power requirement
  • Passes L1/L2 GPS, Galileo & GLONASS
  • Amplified and passive available
  • Mil-Spec options available
APC Technology Group plc

GPS 1×2 Standard Splitter – S12

A GPS splitter allows a single GPS antenna to be shared between multiple GPS receivers.

The S12 GPS splitter is a one-input, two-output GPS device. This product typically finds application where an input from an active GPS roof antenna is split evenly between two receiving GPS units. In this scenario, the S12 can be configured to pass DC from an RF output (J1) to the antenna input port in order to power an active GPS antenna on that port. The second RF output would feature a 200 Ohm DC load to simulate an antenna DC current draw for any receiver connected to that port. This splitters works with distributed antenna systems (DAS).

  • Amplified and passive versions available
  • Frequency response for GPS L1/L2, Galileo, and GLONASS
  • Excellent gain flatness
  • RoHS/WEEE compliant
  • Designed to MIL-STD-810
  • Base Station applications
APC Technology Group plc

GPS 1×2 Slimline Splitter – S12S

The S12S GPS splitter is a one-input, two-output GPS device. This product typically finds application where an input from an active GPS roof antenna is split evenly between two receiving GPS units. In this scenario, the S12 can be configured to pass DC from an RF output (J1) to the antenna input port in order to power an active GPS antenna on that port. The second RF output would feature a 200 Ohm DC load to simulate an antenna DC current draw for any receiver connected to that port.

  • Amplified and passive versions available
  • Frequency response for GPS L1/L2, Galileo, and GLONASS
  • Excellent gain flatness
  • RoHS/WEEE compliant
  • Designed to MIL-STD-810
APC Technology Group plc

GPS 1×4 Standard Splitter – S14

A GPS splitter allows a single GPS antenna to be shared between multiple GPS receivers.The S14 GPS, Galileo, GLONASS splitter is a one input four output RF device. The S14 is available with more options than any comparable product available.

The most common application is the input from an active GPS roof antenna or GPS simulator is equally split to four receiving GPS units. This splitter works well with distributed antenna systems (DAS) and C-RAN.  It will accurately split the timing signal required to synchronise devices.

  • Frequency response for GPS L1/L2, Galileo, & GLONASS
  • Amplified and passive versions available
  • Excellent gain flatness
  • RoHS/WEEE compliant
  • Designed to MIL-STD-810
APC Technology Group plc

GPS 1×4 Slimline Splitter – S14S

The S14S is a slimline version of our bestselling S14. GPS, Galileo, and GLONASS will all pass.  The splitter is a one input four output RF device. This slimline splitter is available with more options than any comparable product available.The most common application is the input from an active GPS roof antenna or GPS simulator is equally split to four receiving GPS units.

  • Frequency response for GPS L1/L2, Galileo, & GLONASS
  • Amplified and passive versions available
  • Excellent gain flatness
  • RoHS/WEEE compliant
  • Designed to MIL-STD-810
APC Technology Group plc

GPS 1×8 Standard Splitter – S18

A GPS splitter allows a single GPS antenna to be shared between multiple GPS receivers.The S18 GPS, Galileo, GLONASS splitter is a one input eight output RF device.

The most common application is where the input from an active GPS roof antenna or GPS simulator is split to eight receiving GPS units. The S18 is available with more customisable options than any competitive product on the market.

  • Passes GPS Galileo, and GLONASS L1/L2
  • Amplified to preserve link margins
  • Excellent gain flatness
  • RoHS/WEEE compliant
  • Designed to MIL-STD-810
APC Technology Group plc

GPS 1×8 Slimline Splitter – S18S

The S18 GPS, Galileo, GLONASS Splitter is a one input eight output RF device. The most common application is where the input from an active GPS roof antenna or GPS simulator is split to eight receiving GPS units. The S18 is available with more customisable options than any competitive product on the market.

  • Passes GPS Galileo, & GLONASS L1/L2
  • Amplified to preserve link margins
  • Excellent gain flatness
  • RoHS/WEEE compliant
  • Designed to MIL-STD-810

 

APC Technology Group plc

GPS 1×4 Wireless Splitter – S14WI

The S14WI is designed to be ruggedized. It can be be configured to monitor the GPS antenna current, providing an alarm indication if the antenna is not operating according to specifications.

The S14WI features an optional DC bias “Pick & Choose” circuit which allows for the active antenna DC input to be appied to any or all of the RF outputs. The S14WI is available with more options than any competitive product on the market. It is especially suited for distributed antenna system (DAS) installations.

  • Ruggedised housing
  • Standard 10dB gain or custom gain options available
  • Optional antenna current monitor and alarm
  • Optional antenna DC bias select
  • Pole-mount environmental housing available (IEC 529 level IP55)
  • Surge protection available
APC Technology Group plc

GPS 1×8 Wireless Splitter – S18WI

The S18WI is designed to be ruggedised. The cost of multiple antennas and long cable runs is eliminated. The S18WI can be configured to monitor the GPS antenna current, providing an alarm indication if the antenna is not operating according to specifications.

The S18WI features an optional DC bias pick and choose circuit which allows for the active antenna DC input to be applied to any or all of the RF outputs. The S18WI is available with more options than any competitive product on the market.

  • Ruggedised housing
  • Standard 10dB gain or custom gain options available
  • Optional antenna current monitor and alarm
  • Optional antenna DC bias select
  • Pole-mount environmental housing available (IEC 529 level IP55)
  • Surge protection available
APC Technology Group plc

Military Qualified 1 x 2 GPS Splitter – MS12

This is a military qualified GPS splitter with one-input and two outputs. It typically finds application where an input from an active GPS roof antenna is split evenly between two receiving GPS units.

The MS12 can be configured to pass DC from an RF output (J2) to the antenna input port in order to power an active GPS antenna on that port. The remaining RF output would feature a 200 Ohm DC load to simulate an antenna DC current draw for any receiver connected to that port.

  • Designed and manufactured to military specifications
  • Amplified and passive versions available
  • Passes GPS, Galileo, and GLONASS L1/L2, protect GPS
  • Excellent gain flatness
APC Technology Group plc

Military Qualified 1 x 4 GPS Splitter – MS14

This is a military qualified MS14 GPS splitter with one-input and four-outputs. It typically finds application where an input from an active GPS roof antenna is split evenly between four receiving GPS units.

The MS14 can be configured to pass DC from an RF output (J2) to the antenna input port (J1) in order to power an active GPS antenna on that port. The remaining RF outputs (J3, J4, and J5) would feature a 200 Ohm DC load to simulate an antenna DC current draw for any receiver connected to that port.

Alternatively, the MS14 can be configured with a MIL-STD-704 compliant 28 VDC Power Supply that will power the active GPS antenna connected to J1

  • Designed and manufactured to military specifications
  • Amplified and passive versions available
  • Passes GPS, Galileo, and GLONASS L1/L2, protect GPS
  • Excellent gain flatness
APC Technology Group plc

Military Qualified 1 x 8 GPS Splitter – MS18

This is a military qualified MS18 GPS splitter with one-input and eight-outputs. It typically finds application where an input from an active GPS roof antenna is split evenly between eight receiving GPS units.

The MS18 can be configured to pass DC from an RF output (J2) to the antenna input port (J1) in order to power an active GPS antenna on that port. The remaining RF outputs (J3 thru J9) would feature a 200 Ohm DC load to simulate an antenna DC current draw for any receiver connected to that port.

  • Designed and manufactured to military specifications
  • Amplified and passive versions available
  • Passes GPS, Galileo, and GLONASS L1/L2, protect GPS
  • Excellent gain flatness

For more information about our range of GPS Source products and technology, contact APC Time on: